manualshive.com logo in svg

ABS MegaCam 4210, User Manual, Page: 36 / 86

Share
Download
ABS MegaCam 4210 User Manual Download Page 36

ABS MegaCam 4210/4220 Network Camera User’s Manual 

 36/86 

up and get a dynamic IP address. For more PPPoE and Internet configuration, please 
consult your dealer or ISP. 

 

The device can directly connect to the xDSL, however, it should be setup on a LAN 
environment to program the PPPoE information first, and then connect to the xDSL 
modem. Power on again, then the device will dial on to the ISP connect to the WAN 
through the xDSL modem.   
   
The procedures are   

• Connect to a LAN by DHCP or Fixed IP   
 
• Access the device, enter 

Setting 

Î

 Network 

Î

 PPPoE 

as below 

 

 

 

PPPoE: 

To enable or disable the PPPoE service here.

 

 

User name: 

 

Type the user name for the PPPoE service which is provided by the ISP.   

Password: 

 

Type the password for the PPPoE service which is provided by the ISP. 

 

 

IP address, Subnet mask, and Gateway (read only): 

Shows the IP information got from PPPoE server site. 

 

Status:

   

Shows the Status of PPPoE connection.   

Summary of Contents for MegaCam 4210























































































Reviews:

No comments