background image

Message

Cause

Action

Date Invalid, 
Check Clock

Date outside six
month lifetime of
software.

Select 5-Clock Set from
Administration Menu. (Password
protected.)

Dead Batteries,
Replace Batteries

Insufficient power to
complete a test cycle.

Replace disposable batteries or
recharge the rechargeable battery.

Temperature Out of
Range, Check
Status page

Temperature outside
operating range of 16
to 30 °C.

Check handheld temperature by
pressing 1 for Analyzer Status under
the Administration Menu. Move
handheld to warmer area if below
operating range or to cooler area if
above the range.

Invalid or Expired
CLEW

Software expired or
corrupt.

Verify that the handheld’s date is
correct. Change software if expired.
Update again if not expired.

Analyzer Interrupted,
Use Another
Cartridge

Last cartridge run not
completed.

Check the battery pack inserted
properly. Check for Low Battery
startup warning.

Cartridge Error

Usually problem with
sample or cartridge
filling.

Use another cartridge. If same code
repeats more than twice, try another
handheld.

Cartridge Preburst

Calibrant pack burst
before cartridge inserted
into handheld.

Use another cartridge - do not press
on center of cartridge. Check that
cartridges have not been frozen.

Unable to Position
Sample

Cartridge not sealed.
Clot in sample.
Aberrant cartridge.

Use another cartridge.

Sample Positioned
Short of Fill Mark

Cartridge underfilled.

Use another cartridge - fill to Fill
Mark.

Sample Positioned
Beyond Fill Mark

Cartridge overfilled.

Use another cartridge - do not fill
beyond Fill Mark.

Test Cancelled by
Operator

User did not respond
to mandatory prompt
before handheld time
out.

No action required.

Cartridge Type Not
Recognized

Software does not
recognize cartridge.

Update software. Check to see if
cartridges are expired.

i-STAT 1

Downloader

Electronic

Simulator

i-STAT Printer

Martel Printer

See System Manual for instructions.

For

in vitro

diagnostic use.

2

Intended Use: The i-STAT 1 Analyzer is intended for use with i-STAT cartridges
for the 

in vitro 

quantification of various analytes in whole blood.

i-STAT 1

Downloader/Recharger

i-STAT Cartridges

System Components

15

Quality Check Messages and Codes

i-STAT 1 Analyzer

Summary of Contents for i-STAT 1









Reviews: