ABB Zenith ZTX Series Operation, Maintenance, And Installation Manual Download Page 67

Page: 67 / 72

—

10. Accessories

Warning

Any installation or maintaining of accessories

should be conducted by trained and autho-

rized personnel only.

Appropriate personal protective equipment

(PPE) shall be used when troubleshooting the

ATS panel.

Hazardous voltage may be present. Discon-

nect all power sources before performing

work inside the ATS panel.

Failure to do so may result in serious injury

or death.

—

10.1 Phase barriers

Phase barriers must be used to maintain a
clearance of 1 inch on the automatic
transfer switch types. They are included
with the shipment of ZTX series ATS
Panel.

—
Fig. 10.1 Mounting of phase barriers, type OXEB_

A07

OXEB_

More information, see animation:
Installation of accessories - TruONE® ATS
(https://youtu.be/qV2KoIv38GY).

Summary of Contents for Zenith ZTX Series









































































Search results

Summary of Contents for Zenith ZTX Series

Reviews:

Related manuals for Zenith ZTX Series

Brands by name

Popular brands

ABB Zenith ZTX Series, Operation, Maintenance, And Installation Manual

Search results

Summary of Contents for Zenith ZTX Series

Reviews:

Related manuals for Zenith ZTX Series

Brands by name

Popular brands