ABB Zenith ZTX Series Operation, Maintenance, And Installation Manual Download Page 41

Page: 41 / 72

—

6.1 Alarms

Alarm condition

Fault

Action

Locked, Alarm LED on

Lock input activated

Unlock

Switch not in AUTO
mode, Alarm LED on

Slide switch is in handle

or lock position

Turn slide switch into

the AUTO position

Phases crossed

Phase rotation of sources 1

and 2 are different

Connect the phases of both sources in

the same order

S1 undervoltage

Voltage of source 1 is under the

threshold level set in parameter

“Dropout voltage, lower threshold“

Check the correlation between power

source and device configuration

S1 overvoltage

Voltage of source 1 is over the

threshold level set in parameter

“Dropout voltage, upper threshold“

Check the correlation between power

source and device configuration

S1 phase missing

One or two phases of

source 1 are missing

Check the power source

and connections

S1 unbalance

Phases of source 1 are not symmetric

Check the power source

S1 phase rotation

Phase rotation of source 1 is

different from the value of

parameter “Phase sequence“

Connect the phases according to the

configuration

Table 6.1 Alarms-list in ZTX via Ekip Connect

—

6. Troubleshooting

Warning

Any troubleshooting should be conducted by

trained and authorized personnel only.

Appropriate personal protective equipment

(PPE) shall be used when troubleshooting the

ATS panel.

Hazardous voltage may be present. Discon

nect all power sources before performing

work inside the ATS panel.

Failure to do so may result in serious injury

or death.

Notice

Alarms, warnings, and information are

directly viewable only via Ekip Programming

or Bluetooth modules

Summary of Contents for Zenith ZTX Series









































































Search results

Summary of Contents for Zenith ZTX Series

Reviews:

Related manuals for Zenith ZTX Series

Brands by name

Popular brands

ABB Zenith ZTX Series, Operation, Maintenance, And Installation Manual

Search results

Summary of Contents for Zenith ZTX Series

Reviews:

Related manuals for Zenith ZTX Series

Brands by name

Popular brands