ABB Zenith ZTX Series Operation, Maintenance, And Installation Manual Download Page 59 | Manualshive

Page: 59 / 72

background image

2

59

Lifting, Mounting and Installation
The safe operation of your switch at all
times is paramount to ABB. Please recog-
nize that hazardous voltages and currents
can exist during normal operation, and
any maintenance on the transfer switch
must be performed utilizing appropriate
safety measures. Installation, adjustment,
maintenance or removal of the switch
must only be carried out by qualified per-
sonnel and with all power to the switch
turned off. It is recommended that only
qualified electricians be allowed to install
or provide maintenance on the switch.

Prior to installation, store the transfer
switch in a clean dry location, protected
from dirt and water. Provide ample air cir-
culation and heat if necessary to prevent
condensation. See table 7.1 for recom-
mended storage and ambient operating
temperatures.

ABB Zenith automatic transfer switches
are packaged as per the standard packag-
ing regulatory standards requirement
suitable for domestic and international
shipment through all modes of transpor-

tation (air, sea and road). Once you un

-

pack the units, please make sure all the
components are received as per the BOM.
For any missing items, contact your local
ABB Zenith service representative.

Danger

Hazardous Voltage can Cause Severe

Injury or Death

Turn OFF all power before installation,

adjustment, or removal of transfer switch

or any of its components.

Warning

Due to hazardous voltages and currents, ABB

recommends that an ABB Certified technician

or a qualified electrician perform the installa-

tion & maintenance of the switch.

Danger

Hazardous Voltage can Cause Severe

Injury or Death

Automatic Transfer Switch Equipment must

be electrically grounded. Failure to do so may

result in malfunction of the switch and possi-

ble damage to surrounding equipment.

Warning

Before drilling conduit entry holes or any ac-

cessory mounting holes, cover and protect

the switch and control panel to prevent dirt

and metal fragments from entering the me-

chanical and electrical components.

—

9.3 Lifting and Mounting the Panel

Lifting guidelines
Adequate lifting means must be used to
mount the transfer switch into place. The
recommended method for moving the
ATS, up to 1200A, is with lifting strap and
lifting equipment rated for the equipment
weight.

«
...
57
58
59
60
61
...
»

Summary of Contents for Zenith ZTX Series









































































Reviews:

No comments

Related manuals for Zenith ZTX Series

Brand: Gefen Pages: 11

xStack DES-3500 Series

Brand: D-Link Pages: 260

DXS-3600 Series

Brand: D-Link Pages: 48

DXS-3400 SERIES

Brand: D-Link Pages: 3

Web Smart Switch DGS-1210-16

Brand: D-Link Pages: 71

Brand: D-Link Pages: 3

Brand: D-Link Pages: 56

xStack DES-3800 Series

Brand: D-Link Pages: 326

xStack DES-3526

Brand: D-Link Pages: 222

Brand: D-Link Pages: 2

DXS-1210 Series

Brand: D-Link Pages: 20

GuardSwitch 300 Series

Brand: GE Pages: 4

Brand: IBM Pages: 156

Brand: Dataprobe Pages: 21

Brand: Cabletron Systems Pages: 52

Brand: Hanwell Pages: 109

Brand: Olympia Pages: 6

tekmarNet4 User Switch 480

Brand: Tekmar Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands