ABB XAC24427 Operation Manual Download

Page: 77 / 140

Operation Manual / 4 Product description / A100-L

7 Troubleshooting / 7.2 Malfunctions during operation

HZTL4034_EN

Rev.S

May 2021

7.2

Malfunctions during operation

Lubricating oil pressure too low

WARNING

Danger of fire and explosion due to lubricating oil leaks

Leaking oil may ignite on hot surfaces. This can result in serious injuries to
personnel or fatal accidents.

Cordon off danger area.

Raise the alarm and, depending on the situation, stop the engine.

Seal the oil leak.

Soak up oil and dispose of in an environmentally compatible manner.

Wear safety gloves to protect against thermal hazards.

Possible causes

Remedy

Turbochar-
ger

Axial clearance of the rotor excessive

Contact an ABB Turbocharging
Service Station

Engine

Oil filter heavily contaminated

Clean

Oil pump in lubricating system defect-
ive

Check/replace

Manometer displays incorrectly

Replace manometer

Table 18: Malfunctions during operation – Lubricating oil pressure too low

Drop in speed

Possible causes

Remedy

Turbochar-
ger

Heavy contamination of the turbine

Clean

Damaged rotor components or bearing Contact ABB Turbocharging Service

Station

Pipes

Defects, such as leaks, in the exhaust
gas pipes or charge air ducts

Repair

Table 19: Malfunctions during operation – Drop in speed

Page

110

Summary of Contents for XAC24427












































































































































Search results

Summary of Contents for XAC24427

Reviews:

Related manuals for XAC24427

Brands by name

Popular brands

ABB XAC24427, Operation Manual

Search results

Summary of Contents for XAC24427

Reviews:

Related manuals for XAC24427

Brands by name

Popular brands