ABB XAC24427 Operation Manual Download

Page: 118 / 140

Operation Manual / 4 Product description / A100-L

8 Disassembly and assembly / 8.23 Fitting the filter silencer with noise
package

HZTL4034_EN

Rev.S

May 2021

1. Position segments of the gasket (81301) on threaded studs of the compressor cas-

ing (72000).

2. Attach the lifting gear to the front lug and rear eyelet of the filter silencer (81000), paying

attention to the version of the filter silencer.

3. Position filter silencer on compressor casing.

4. Fit nuts (72004) with washers (72003) and insulating discs (81302) and tighten.

5. Fit insulation ring (81300).

6. Fit air outlet silencer (74040) with gasket (74042) and secure with counter-sunk

screws (74043).

Fit insulation as far as necessary.

Page

110

Summary of Contents for XAC24427












































































































































Search results

Summary of Contents for XAC24427

Reviews:

Related manuals for XAC24427

Brands by name

Popular brands

ABB XAC24427, Operation Manual

Search results

Summary of Contents for XAC24427

Reviews:

Related manuals for XAC24427

Brands by name

Popular brands