ABB XAC24427 Operation Manual Download

Page: 140 / 140

Operation Manual / 4 Product description / A100-L

Tables

HZTL4034_EN

Revision S

May 2021

Tables

Table 1: Related documents ......................................... 4

Table 2: Total weight ..................................................... 9

Table 3: General information about fastening the
turbocharger .................................................................. 12

Table 4: Tightening torques (foot screws) .............. 13

Table 5: Tightening angle (foot screws)................... 13

Table 6: Lubricating oil pressure, oil inlet ............... 17

Table 7: Lubricating oil temperature at the inlet ... 18

Table 8: Lubricating oil temperature at the outlet. 18

Table 9: Tightening torques (86505)......................... 22

Table 10: Expected replacement intervals for tur-
bocharger parts ........................................................... 29

Table 11: Recommended replacement intervals for
turbocharger parts ..................................................... 29

Table 12: Volume of water per cleaning process.... 40

Table 13: Tightening torques (81125) ....................... 40

Table 14: Amount of granulate .................................. 44

Table 15: Malfunctions when starting – Delayed
start-up .......................................................................... 46

Table 16: Malfunctions when starting – Vibrations 46

Table 17: Malfunctions when starting – Rubbing of
rotating parts................................................................ 46

Table 18: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 47

Table 19: Malfunctions during operation – Drop in
speed ............................................................................. 47

Table 20: Malfunctions during operation – Exhaust
gas temperature too high .......................................... 48

Table 21: Malfunctions during operation – Charge air
pressure too low........................................................... 48

Table 22: Malfunctions during operation – Charge air
pressure too high ......................................................... 49

Table 23: Surging of the turbocharger..................... 49

Table 24: Malfunctions when stopping – Runout
noises.............................................................................. 50

Table 25: Malfunctions when stopping – Shortened
runout time.................................................................... 50

Table 26: Malfunctions of the speed measurement
system ............................................................................. 51

Table 27: Weights of assemblies [kg] ........................ 54

Table 28: Weight of wall insert [kg] ........................... 54

Table 29: Tightening torques (filter silencer screws)..
59

Table 30: Axial clearance A........................................... 67

Table 31: Maximum admissible loosening torque
(51087) ............................................................................. 69

Table 32: Maximum admissible loosening torque
(51087) .............................................................................. 71

Table 33: Tightening torque (56014) ......................... 74

Table 34: Tightening torque (51087) ......................... 75

Table 35: Tightening torque (56014) ......................... 78

Table 36: Tightening torque (51087) ......................... 79

Table 37: Axial clearance A ........................................... 80

Table 38: Tightening torque (77015).......................... 81

Table 39: Tightening torque (72011) .......................... 83

Table 40: Tightening torque (72004)......................... 85

Table 41: Tightening torque (72004) ......................... 86

Table 42: Tightening torque (51087) ......................... 87

Table 43: Overview of tightening torques ................ 90

Table 44: Tightening torque, insulation.................... 90

Table 45: Bypass procedure ........................................ 92

Table 46: Tightening torque B

, B

.............................. 94

Table 47: Required washers (01)................................. 95

Table 48: Tightening torque (57005)......................... 95

Table 49: Customer spare part set (97070) ........... 101

Table 50: Customer spare part set (97071) ............ 102

Table 51: Turbocharger with part numbers............ 104

Table 52: Cartridge group with part numbers ....... 106

Table 53: Customer tool set 90000 ......................... 107

Page

110

Page

110

Summary of Contents for XAC24427












































































































































Search results

Summary of Contents for XAC24427

Reviews:

Related manuals for XAC24427

Brands by name

Popular brands

ABB XAC24427, Operation Manual

Search results

Summary of Contents for XAC24427

Reviews:

Related manuals for XAC24427

Brands by name

Popular brands