ABB XAC24427 Operation Manual Download

Page: 115 / 140

Operation Manual / 4 Product description / A100-L

8 Disassembly and assembly / 8.22 Fitting the filter silencer

HZTL4034_EN

Rev.S

May 2021

8.22.2

Fitting the filter silencer (welded)

If the turbocharger is also fitted with a noise package, chapter

Fitting the filter silencer with

noise package

→

must be observed.

Fig. 56: Fitting the filter silencer

Product

Size

Tightening torque [Nm]

A165-L

M14

130

A170-L

M16

200

A175-L

M18

300

A180-L

M20

420

A185-L

M22

570

A190-L

M24

710

Table 40: Tightening torque (72004)

1. Attach lifting gear to the eyelets of the filter silencer (81000).

2. Position filter silencer on compressor casing.

3. Fit nuts (72004) with washers (72003) and tighten.

Fit insulation as far as necessary.

Page

110

Summary of Contents for XAC24427












































































































































Search results

Summary of Contents for XAC24427

Reviews:

Related manuals for XAC24427

Brands by name

Popular brands

ABB XAC24427, Operation Manual

Search results

Summary of Contents for XAC24427

Reviews:

Related manuals for XAC24427

Brands by name

Popular brands