ABB XAC24427 Operation Manual Download

Page: 68 / 140

Operation Manual / 4 Product description / A100-L

6 Periodic maintenance / 6.4 Cleaning the compressor during opera-
tion

HZTL4034_EN

Rev.S

May 2021

Principle of wet cleaning

CAUTION

Corrosion and deposits when cleaning

Salt water and cooling water treatment substances damage and adversely
affect turbocharger parts.

Never use salt water, but only pure water for cleaning.

To clean the compressor stage during operation, water is injected upstream of the com-
pressor wheel.

The water does not act as a solvent. The coating is removed by the mechanical action of the
impacting droplets. The procedure is perfectly suitable, provided that the contamination
has not progressed too far.

Cleaning several turbochargers

If several turbochargers are installed on an engine, it is recommended to clean one com-
pressor after the other.

CAUTION

Volume of water for cleaning the compressor

Uncontrolled volumes of water can damage the turbocharger and the en-
gine.

Do not guide water pipes to the filler openings.

Page

110

Summary of Contents for XAC24427












































































































































Search results

Summary of Contents for XAC24427

Reviews:

Related manuals for XAC24427

Brands by name

Popular brands

ABB XAC24427, Operation Manual

Search results

Summary of Contents for XAC24427

Reviews:

Related manuals for XAC24427

Brands by name

Popular brands