ABB XAC24427 Operation Manual Download | Manualshive

Page: 39 / 140

background image

Operation Manual / 4 Product description / A100-L

2 Removal and installation / 2.1 Turbocharger weight

© Copyright 2021 ABB. All rights reserved.

HZTL4034_EN

Rev.S

May 2021

2

Removal and installation

2.1

Turbocharger weight

Lifting gear with a sufficient load limit must be used for removing, installing and transport-
ing the turbocharger. The weight specified below applies to the heaviest variant possible.
Depending on the specification, the weight specified on the rating plate may be lower than
the standard value specified here.

Product

Weight of complete turbocharger unit [kg]

A165-L

2300

A170-L

3300

A175-L

5600

A180-L

7500

A185-L

10500

A190-L

13500

Table 2: Total weight

2.2

Removing the turbocharger

WARNING

Risk of tipping

If the turbocharger is not sufficiently supported or not supported at all dur-
ing removal and installation, it may tip over and cause severe injury to per-
sonnel or accidents resulting in fatalities.

u

Support the turbocharger at a suitable location.

u

Secure with lifting gear wherever possible.

u

Loosen cable to speed sensor.

u

Disconnect all pipes according to the instructions of the enginebuilder.

u

Check lifting gear.

u

Attach lifting gear to the turbocharger and tauten.

Page

9

/

110

«
...
37
38
39
40
41
...
»

Summary of Contents for XAC24427













































































































































Reviews:

No comments

Related manuals for XAC24427

Brand: Parallax Pages: 10

Brand: Wallbox Pages: 34

DBU-3200 Series

Brand: Mean Well Pages: 18

Brand: SUEX Pages: 32

Brand: Calira Pages: 56

Stratos IRC 1721

Brand: Invacare Pages: 16

Brand: ABL Pages: 94

LIBERTY 1000 Series

Brand: C&D Technologies Pages: 43

XD P322.43 Series

Brand: XD COLLECTION Pages: 20

Brand: CHARGEHUB Pages: 34

Brand: CTEK Pages: 7

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands