ABB UNO-DM-2.0-TL-PLUS Manual Download Page 6

Page: 6 / 198

- 6 -

001033BG

Communication and control signal connections to the UNO-DM-COM KIT board ......................78

Description of terminal blocks on the UNO-DM-COM KIT board .........................................79

Description of terminal blocks on the UNO-DM-PLUS-COM Ethernet KIT board ...............80

Connection of the RS485 line ...............................................................................................................81

Remote control connection ...................................................................................................83

Demand Responce Mode 0 (Request by AS/NZS 4777) .....................................................83

Configurable Relay connection (ALARM / LOAD MANAGER) ...........................................84

Connection of the energy meter .........................................................................................................85

Connection of the REACT-MTR-1PH (single-phase) ...........................................................85

Connection and configuration of the ABB B21 meter (single-phase) ...................................87

Connection and configuration of the ABB B23, B24 3PH (three-phase) ..............................90

Closing the front cover ........................................................................................................................93

nstruments ........................................................................................................................................94

General conditions ..............................................................................................................................94

Monitoring and data transmission .....................................................................................................95

User interface ........................................................................................................................95

Measurement tolerance ........................................................................................................95

Description of keyboard and LED Panel...............................................................................96

peration ..........................................................................................................................................97

General conditions ..............................................................................................................................97

Commissioning (Via web user interface) ...........................................................................................98

Commissioning (Using the inverter display) ...................................................................................107

Power, Alarm, GFI LEDs behaviour ..................................................................................................109

Specifications on operation of the LEDs .............................................................................110

LED insulation fault .............................................................................................................110

COMM, WLAN LEDs behaviour .........................................................................................................110

Description of the Web user interface .............................................................................................111

Access to the Web user interface ....................................................................................... 111

web user interface menu structure .....................................................................................114

MAIN section .......................................................................................................................115

SETUP section ....................................................................................................................116

EVENTS Section .................................................................................................................118

USER section ......................................................................................................................119

NETWORK section .............................................................................................................120

TOOLS section ....................................................................................................................124

INFORMATION Section ......................................................................................................135

Description of the Display menus ....................................................................................................136

General information ............................................................................................................136

Menu structure ....................................................................................................................137

System Menu ......................................................................................................................138

Inverter Menu ......................................................................................................................140

Display Menu ......................................................................................................................154

WLAN Logger Menu ...........................................................................................................155

Summary of Contents for UNO-DM-2.0-TL-PLUS







































































































































































































Search results

Summary of Contents for UNO-DM-2.0-TL-PLUS

Reviews:

ABB UNO-DM-2.0-TL-PLUS, Manual, Page: 6 / 198

Search results

Summary of Contents for UNO-DM-2.0-TL-PLUS

Reviews: