ABB Terra 124 Installation Manual Download

Page: 39 / 54

8.3

General specifications

Parameter

Specification

Compliance and safety

CE
CHAdeMO 1.2

IP rating

The type plate shows the specification.

Refer to section

2.1

IK rating according to IEC 62262: enclo-

sure

IK10

IK rating according to IEC 62262:

touchscreen

IK08

EMC rating

Class B

8.4

Required tools for installation

Parameter

Specification

Philips screwdriver

Size: PH2

Slot screwdriver

Size: 4.5 and 2.5 mm

Hex keys

Size: 5, 5.5 and 6 mm

Torx screwdriver

Size: 15, 20 and 25

Torx angled or bit with ratchet

Size: 20

Open spanner

Size: M5 (8mm), M6 (10 mm), M10 (15

mm), M12 (19 mm) and M16 (24 mm)

Torque socket wrench

5 to 20 Nm, size M8 (13 mm) and M6 (10

mm)

Ratchet spanner with socket and exten-

sion

Size: M5 (8 mm) and M6 (10 mm)

Tie-wraps

Standard

Voltage tester

To switch 200 mA of test current (exam-

ple: Duspol)

Digital multimeter

Standard

Hoisting equipment or forklift truck

Capable to lift the EVSE safely. Take into

account the dimensions, the mass, the

center of gravity and the maximum tilt

angle. Refer to different sections in this

document.

Swivel eye bolts or bolts with lifting

loops (to use with hoisting equipment)

Thread M10

Wire stripper pliers

To strip the wires of the AC input cable

Wire end ring tool

Size: M11

Technical data

BCM.S1102.0-EN | 001

Summary of Contents for Terra 124





















































Search results

Summary of Contents for Terra 124

Reviews:

Related manuals for Terra 124

Brands by name

Popular brands

ABB Terra 124, Installation Manual

Search results

Summary of Contents for Terra 124

Reviews:

Related manuals for Terra 124

Brands by name

Popular brands