ABB Terra 124 Installation Manual Download

Page: 11 / 54

Description

2.1

Type plate

IP54

SN: XXXX-XXX-XXXX-XXX

Part number XXXXXXXXXX

Prod. date XX XXXX

XXXXXXXXXXXX

XX XXXXX XX

FOR USE WITH ELECTRICAL VEHICLES

Input

xxxV x+PE-

DC Input

xxx-xxxV Max xxxA

DC Output 1 CCS2

xxx-xxxV Max xxxA

DC Output 2 CHAdeMO xxx-xxxV Max xxxA

Max x.xkW/xxHz

DC AUX xxV xA

George Hintzenweg 81,
3068 AX Rotterdam,
The Nederlands

MADE IN ITALY

www.abb.com

Weight XXX Kg

XXXXXXXXXX

XXXX-XXX-XXXX-XXX

Manufacturer

Serial number

Part number of the EVSE

Production date

Internal product code (for the

manufacturer)

Full EVSE type

EVSE mass

EVSE rating

Address of the manufacturer

CE mark

Barcode with the serial number of

the EVSE

Barcode with the part number of

the EVSE

Additional EVSE rating data

Note: Find the type plate on your EVSE to see the applicable data. Refer

to section

2.4.2

2.2

Intended use

The EVSE is intended for the DC charging of EVs. The EVSE is intended for indoor or

outdoor use.

The properties of the electrical grid, the ambient conditions and the EV must

comply with the technical data of the EVSE. Refer to chapter

Only use the EVSE with accessories that the manufacturer provides and that obey

the local rules.

Description

BCM.S1102.0-EN | 001

Summary of Contents for Terra 124





















































Search results

Summary of Contents for Terra 124

Reviews:

Related manuals for Terra 124

Brands by name

Popular brands

ABB Terra 124, Installation Manual

Search results

Summary of Contents for Terra 124

Reviews:

Related manuals for Terra 124

Brands by name

Popular brands