ABB Terra 124 Installation Manual Download

Page: 45 / 54

Ethernet cable

Parameter

Specification

Ethernet type

RJ45

Cable type

8P + PE, shielded

Example of a cable for distance of 75 m

or less

HELUKAT 600E

Bandwidth, upload

Minimum 128 kbit/s

Bandwidth, download

Minimum 4 Mbit/s

Availability

99.9%

8.12

AC input specifications

8.12.1

General AC input specifications

Parameter

Specification

Input AC power connection

3P + N + PE

Earthing systems

TN-S
TN-C
TN-C-S
IT

Input voltage range

400 VAC +/- 10% (50 Hz or 60 Hz)

Power factor at full load

> 0.96

Efficiency

> 94% at nominal output power

Total harmonic distortion (current)

< 5%

8.12.2

AC input cable

Parameter

Specification

Cable shielding (optional)

If the local rules require shielded cables,

the cable shielding must be connected

to the PE rail at both ends of the cable.

Diameter of the phase conductors

Refer to the local rules.

Diameter of the PE conductor

The same as the diameter of the phase

conductors

Surface

minimum 150 mm²

Diameter, including shielding

34 to 45 mm

8.12.3

Terra 94

Parameter

Specification [A]

Maximum rated input current

140

Technical data

BCM.S1102.0-EN | 001

Summary of Contents for Terra 124





















































Search results

Summary of Contents for Terra 124

Reviews:

Related manuals for Terra 124

Brands by name

Popular brands

ABB Terra 124, Installation Manual

Search results

Summary of Contents for Terra 124

Reviews:

Related manuals for Terra 124

Brands by name

Popular brands