background image

SPECIFICATIONS

Input:  

18V

Battery Power: 

2.0Ah Li-Ion

  4.0Ah 

Li-Ion

Kit Charge Time: 

40min (2.0Ah Battery)

 

 

80min (4.0Ah Battery)

Weight:  

1.65kg

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR 

YOUR BATTERY CHARGER.

1. 

Before using the charger read all instructions and cautionary markings on the charger, 

battery pack and the product using the battery pack.

2. 

This charger is not intended for any uses other than charging rechargeable batteries. 

Any other use may result in risk of fire, electric shock or electrocution.

3. 

Do not place any object on top of the charger or place the charger on a soft surface 

that may result in excessive internal heat. Place the charger in a position away from 

any heat source.

4. 

To reduce risk of damage to the electric plug and cord, pull by the plug rather than 

the cord when disconnecting the charger.

5. 

Make sure the cord is located so that it will not be stepped on, tripped over, or 

otherwise subjected to damage or stress.

6. 

An extension cord should not be used unless absolutely necessary. Use of an improper 

extension cord could result in the risk of fire, electric shock or electrocution.

7. 

Do not operate the charger if it has received a sharp blow, been dropped or otherwise 

damaged in any way. Have it checked by an electrician or power tool repairer.

8. 

Do not disassemble charger. Take it to an electrician or power tool repairer when 

service or repair is required. Incorrect reassembly may result in a risk of electric 

shock, electrocution or fire.

9. 

To reduce risk of electric shock, unplug the charger from the outlet before attempting 

any cleaning. Removing the battery pack will not reduce this risk.

10.  Never attempt to connect 2 chargers together.

11.  DO NOT store or use the tool and battery pack in locations where the temperature may 

reach or exceed 40ºC (such as inside sheds or metal buildings in summer).

12.  The charger is designed to operate on standard household electrical power (240 

volts). Do not attempt to use it on any other voltage!

13.  The battery pack is not fully charged out of the carton. First read the safety instruc-

tions and then follow the charging notes and procedures.

14.  The longest life and best performance can be obtained if the battery pack is charged 

when the air temperature is between 18 - 24ºC. Do not charge the battery pack in an 

air temperature below 10ºC or above 40ºC. This is important and will prevent damage 

to the battery pack.

15.  Do not incinerate the battery pack even if it is seriously damaged or is completely worn 

out. The battery can explode in a fire.

16.  Never attempt to open the battery pack for any reason. If the plastic housing of the battery 

pack breaks or cracks, immediately discontinue use and do not recharge.

17.  During charging, the battery must be placed in a well ventilated area.

BATTERY & CHARGER SAFETY WARNINGS

 ELECTRICAL SAFETY

 

WARNING!

 

When using mains-powered tools, basic safety precautions, 

including the following, should always be followed to reduce risk of fire, electric 

shock, personal injury and material damage. 

Read the whole manual carefully and make sure you know how to switch the tool off in an 

emergency, before operating the tool. 

Save these instructions and other documents supplied with this tool for future reference.
Before you connect the charger to the mains supply make sure that the data on the rating 

plate are identical to the mains data.

This tools charger is double insulated, therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or 

similarly qualified persons in order to avoid hazard.

Note: Double insulation does not take the place of normal safety precautions when 

operating this tool. The insulation system is for added protection against injury resulting 

from a possible electrical insulation failure within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before 

use, inspect the extension lead for signs of damage, wear and ageing. Replace the 

extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an 

extension lead not suitable for the power input of the tool or which is damaged or defective 

may result in a risk of fire and electric shock.
To reduce the risk of electric shock, we recommend the use of a residual current device 

(rated 30mA or less).
This appliance is not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been 

given supervision or instruction concerning use of the appliance by a person responsible for 

their safety.
Children should be supervised to ensure that they do not play with the appliance.

1.  Battery Release Button
2.  Charge Indicator Button 
3.   2.0Ah Battery
4.  4.0Ah Battery
5.  Charging Unit LED
6.  Charging Unit

ozito-diy.co.uk

DESCRIPTION OF SYMBOLS

1 2

3

4

CHARGER & 

BATTERY PACK

ORIGINAL INSTRUCTIONS

PXBC-007U

6

5

Warning 

Do not use or store battery in 
temperatures exceeding 50ºC

   

Volts

Hertz

Alternating Current

Direct Current

Milliamperes

Watts

Amp Hour

Ah

W

Hz

V

ac/~

mA

Lithium Ion Battery

Do not put in the rubbish

Do not get battery wet

Recycle Battery

Do not incinerate

dc

Read instruction manual

Double insulated

Indoor use only

Thermal cut out

protection

Reviews: