ABB Smart BTRF-37C16A, Operator'S Manual, Page: 4 / 16

– Standard Lug - If the last operation
performed was crimping a standard
connector, the display will indicate
"Standard Lug" along with the size and type
of connector.
Example:
Standard Lug
Size: 500 kcmil
Type: Copper
The display indicates the
type and size. Additional crimps will
continue to be logged without a S/N, along
with the Tool ID, final dimension, final
pressure, date/time code, and pass/fail until
a new connector is scanned or manually
entered.
5.3 Back up release valve
• Before opening the head during an incomplete
crimp cycle, first: press and hold the backup
release valve.
6.0 Maintenance
6.1 WARNING
• Always unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never
disassemble the tool, battery pack or charger.
Contact an ABB tool service for ALL repairs.
• Always remove battery pack before changing or
removing accessories. Only use accessories
specifically recommended for this tool.
6.2 To replace coin cell battery
1) Remove battery pack.
2) Remove screw and open battery door.
3) Remove old battery, keep it away from children,
and dispose of it properly.
4) Insert new battery (3V CR2032), positive side
facing up.
5) Close battery door and tighten screw securely.
6) After changing internal battery, reset internal
Tool Time to current UTC time to support
continued accurate date/time reporting. Set
tool time using settings menu of Smart® Tool +
mobile application.
6.3 Maintaining the tool
• Follow a regular maintenance program. In the
event of undue noise, misalignment or binding
of moving parts, breakage of parts, or any
other condition that may affect the tool
operation, return the tool, battery pack, and
charger to ABB Service for repair.
• If the tool does not start or operate at full
power with a fully charged battery pack, clean
the contacts on the battery pack. If the tool still
does not start or operate at full power, return
the tool, charger and battery pack, to ABB tool
service for repairs.
6.4 Cleaning
• Keep vents free of dust and debris.
• Keep handles clean, dry and free of oil or
grease. Use only mild soap and a damp cloth to
clean. Other cleaning agents and solvents are
harmful to plastics and other insulated parts.
• Never use flammable or combustible solvents
such as gasoline, turpentine, lacquer thinner,
paint thinner, chlorinated cleaning solvents,
ammonia and household detergents
containing ammonia around tools.
6.5 Service and repairs
• Power tool, battery pack and charger must be
serviced by manufacturer or authorized service
provider.
• For all warranty, customer service, and product
return authorizations and inquiries, please
contact:
– ABB, Memphis, TN (USA)
– Technical services: 1-888-862-3289
– Tool Service 1-800-284-TOOL (8665)
– Web site: www.tnb.com
7.0 Federal Communications Commission
• Contains ThingMagic Inc. ThingMagic Nano
transmitting module FCC ID: QV5MERCURY6EN
(IC: 5407A-MERCURY6EN). Modular
Certification using equivalent antenna with -1.0
dBiL gain. To comply with FCC's RF radiation
exposure requirements, the antenna used for
this transmitter must be installed such that a
minimum separation distance of 21 cm is
maintained between the radiator (antenna) &
user's/nearby people's body at all times and
must not be co-located or operating in
conjunction with any other antenna or
transmitter. The Transmitting portion of this
device carries with it the following two
warnings: "This device complies with Part 15",
and "Any changes or modifications to the
transmitting module not expressly approved by
ThingMagic Inc. could void the user's authority
to operate this equipment."
STANDARD LUG
500 kcmil Cu
4