manualshive.com logo in svg

ABB Navigator 540, Instruction Manual

Share
Download
ABB Navigator 540 Instruction Manual Download Page 8

8

COM/AWT540/PB–EN Rev. C

| Navigator 540 | Transmitter

4 PROFIBUS communications

This section contains information specific to the 
PROFIBUS

®

-enabled Navigator AWT540 with RS485 physical 

layer. 

It must be read in conjunction with the associated Operating 
instructions: 

— Sodium: OI/ASO550-EN

— Dissolved oxygen: OI/ADS550-EN

— Hydrazine: OI/AHM550-EN

Refer the associated data sheets for details of specific order 
codes:

— Sodium: DS/ASO550-EN

— Dissolved oxygen: DS/ADS550-EN

— Hydrazine: DS/AHM550-EN

4.1 PROFIBUS DP transmission technology

The most common transfer method of PROFIBUS-DP is RS485 
– a proven technology. A twisted, shielded, 2-wire copper 
cable is used as the transfer medium. 

The bus structure enables addition and removal of stations or 
step-by-step commissioning of the system without affecting 
other stations. Later expansion has no influence on stations 
already in operation.

Transmission speeds from 9.6 kbps up to 12 Mbps are 
supported. One uniform transmission speed is selected for all 
devices on the bus when the system is commissioned.

4.2 Acronyms and abbreviations

4.3 PROFIBUS interface

4.4 Installation

4.4.1 Installation overview

All devices are connected in a bus structure ('line') as shown in 
Fig 4.1. Up to 32 stations (master or slaves) can be linked to 
create one 'segment', although it is recommended not to install 
more than 16 devices on a single segment. 

Each end of a segment must be terminated by an active bus 
terminating resistor. Both bus terminators must always be 
powered to ensure fault-free operation, therefore it is strongly 
recommended that they are connected to a back-up power 
supply. The use of bus amplifiers (repeaters) and segment 
couplers can be used to extend the network. 

Input

Data passed into a Master device 

(for example, from a Slave device)

I&M

PROFIBUS identification 
and maintenance function 

MS1

Class 1 Master-Slave acyclic transaction

Output

Data passed out of a Master device 
(for example, to a Slave device)

PCS/DCS

Process control system / 

distributed control system

PI/PNO

PROFIBUS International / PROFIBUS User 

Organization (www.profibus.com)

TB

PROFIBUS-PA transducer block

TOT

Totalizer function block

Table 4.1: Acronyms and abbreviations

Physical layer

RS485

Supported baud rates

9.6 kbps to 12 Mbps

Supported DP Protocol 
services

DPV0, DPV1

Concurrent MS2 
connections

3

Device stub length

250 mm (9.8 in.)

Application profile

PA version 3.01

Master components 
available

GSD, DTM, EDD

Table 4.2: PROFIBUS interface

Fig. 4.1: Typical PROFIBUS network

Operational 
level

Master 
level

Slave 
level

Engineer

Operate

Control

PROFIBUS-DP

DP / PA link

PROFIBUS-P

Navigator AWT540

transmitter

Summary of Contents for Navigator 540























































Reviews:

No comments

Brands by name

Popular brands

Load more brands