background image

12 

Software WIN-PC for Intrusion Alarm Panel L240

4.2  

Connection to the panel 
 

 

After the customer account is created, a connection with 

the Intrusion Alarm Panel L240 can be established. For this purpose, 
go to the “Panel Connection” in the customer tree and then click on the 
“Connect” button in the main window. After a connection is established, 
the following message is shown: “Connected to Panel: Please select an 
option from the connection tree on the left”. 

If the connection cannot be established, please check the settings in the 
Intrusion Alarm Panel L240 again; refer to Chapter 3 “Connection points 
to the panel L240”.

 

Now WIN-PC can read in the configuration data of 

the Intrusion Alarm Panel L240. For this purpose, press the “Read 
Configuration” button under “Panel Connection” in the submenu 
“Configuration”. The transfer may take a few minutes depending on the 
amount of data to be transferred.

Note:

After reading of the panel data, you should again check whether the con-
nection settings to the interfaces in your customer tree have been correctly 
accepted by the panel. In the customer tree under “Configuration” sub 
point “Remote”, the items Connection, Operations, User Auth and SiteIP 
must correspond with the settings in the panel. Otherwise you must 
correct these settings.

Editing the configuration data 

The configuration can be edited after reading the data. After ending of 
WIN-PC, this data can be automatically stored in the customer account. 

 In order to send the configuration data to the Intrusion 

Alarm Panel L240, press the “Write Configuration” button under “Panel 
Connection” in sub point “Configuration”.

Summary of Contents for L240 Series





















Reviews: