manualshive.com logo in svg

ABB IEC 60870-5-103, Communication Protocol Manual

Share
Download
ABB IEC 60870-5-103 Communication Protocol Manual Download Page 31

Name

Values (Range)

Unit

Step

Default

Description

MaxIN

1 - 99999

A

1

3000

Maximum residual current IN

MaxUL1

0.05 - 2000.00

kV

0.05

230.00

Maximum voltage for phase L1

MaxUL2

0.05 - 2000.00

kV

0.05

230.00

Maximum voltage for phase L2

MaxUL3

0.05 - 2000.00

kV

0.05

230.00

Maximum voltage for phase L3

MaxUL1-UL2

0.05 - 2000.00

kV

0.05

400.00

Maximum voltage for phase-phase L1-L2

MaxUN

0.05 - 2000.00

kV

0.05

230.00

Maximum residual voltage UN

MaxP

0.00 - 2000.00

MW

0.05

1200.00

Maximum value for active power

MaxQ

0.00 - 2000.00

MVAr

0.05

1200.00

Maximum value for reactive power

MaxF

15.0 - 66.0

Hz

1.0

51.0

Maximum system frequency

4.1.1.5 

Supported information types

Measurands in public range, I103MEAS

M11874-385 v8

Number of instances: 1

The IED reports all valid measuring types depending on connected signals.

Upper limit for measured currents, active/reactive-power is 2.4 times rated value.

Upper limit for measured voltages and frequency is 1.2 times rated value.

The upper limit is the maximum value that can be encoded into the ASDU
(Application Service Data Unit). Any value higher than this value will be tagged as
OVERFLOW. The factors 1.2 and 2.4 are taken from the 103 standard and require
that a rated value to use as base exists, and then use 1.2 or 2.4 times <rated> as

maxVal

. You can use 2.4 times rated as 

maxVal

, but as there is no way to propagate

value to client, the use of a scale factor on <rated> does not make much difference.

You can configure client:

client-scaled-max ::= 1.2 * <rated>

 or

client-scaled-max ::= 1.0 * <maxVal>

If the client has a hard-coded gain of 1.2 * <rated> then 

client-scaled-

max ::= 1.2 times <maxVal>/1.2

Resolution is <maxVal> / 4095 and hence the lowest possible 

maxVal

 yields the

best accuracy.

Table 6:

I103MEAS supported indications

INF

Description

148

IL1

144, 145,

146, 148

IL2

148

IL3

147

IN, Neutral current

148

UL1

Table continues on next page

1MRK 511 394-UEN A

Section 4

IEC 60870-5-103 vendor specific implementation

670 series 2.2 IEC

25

Communication protocol manual

Summary of Contents for IEC 60870-5-103

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands