ABB i-bus KNX SUG/U 1.1 Page 5 Product Manual Download | Manualshive

Page: 5 / 56

background image

ABB i-bus

®

KNX

General

SUG/U 1.1 | 2CDC508171D0201 3

1

General

This manual provides detailed technical information concerning the ABB i-bus

®

KNX SUG/U 1.1

Split Unit Gateway.

Split units are HVAC devices which are usually operated by an infrared remote control. The Split Unit
Gateway is installed near the split unit and the transmitter of the supplied cable is bonded to the receiver of
the unit itself. This makes it possible to control the split unit via KNX group commands. The Split Unit
Gateway allows users to integrate the split unit in a KNX system for convenient, energy efficient control.

1.1

Using the product manual

This manual provides detailed technical information on the function, installation and programming of the
ABB i-bus

®

KNX device. Explanations on how to use it are accompanied by examples.

This manual is divided into the following chapters:

Chapter 1

General

Chapter 2

Device technology

Chapter 3

Commissioning

Chapter A

Appendix

«
...
3
4
5
6
7
...
»

Summary of Contents for i-bus KNX SUG/U 1.1

























































Reviews:

No comments

Related manuals for i-bus KNX SUG/U 1.1

Brand: Kuhnt Pages: 173

SBO500 SBO Series

Brand: Synway Pages: 72

EliteConnect SMCWHSG14-G

Brand: SMC Networks Pages: 2

Brand: Juniper Pages: 3

Brand: ZyXEL Communications Pages: 2

Brand: ProSoft Pages: 157

Brand: ProSoft Technology Pages: 154

Brand: Lantronix Pages: 2

Brand: Festo Pages: 4

Brand: Festo Pages: 78

Brand: Cell2Tel Pages: 34

Brand: Bpt Pages: 25

Fieldgate SFG500

Brand: Endress+Hauser Pages: 52

Firebox SSL Core

Brand: Watchguard Pages: 20

SmartLINK Ei1000G

Brand: Ei Electronics Pages: 16

Brand: NavCom Technology Pages: 7

Brand: Black Box Pages: 9

WaveBase Pro Series

Brand: Nexland Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands