manualshive.com logo in svg

ABB i-bus KNX SUG/U 1.1, Product Manual, Page: 10 / 56

Share
Download
ABB i-bus KNX SUG/U 1.1 Product Manual Download Page 10

ABB i-bus

®

 KNX 

Device technology 
 
 

8   2CDC508171D0201 | SUG/U 1.1 

Device type 

Application 

Maximum number of 
group objects 

Maximum number of 
group addresses 

Maximum number of 
assignments 

SUG/U 1.1 

Split Unit Gateway/…* 

30 

255 

255 

 

 

 

 

 

* … = Current version number of the application. 

Please refer to the software information on our website for this purpose.

 

 

Note 

The Engineering Tool Software, ETS, version 4.2.0, 5.5.3 or later, and the current device application are 
required for programming. 
The current application is available for download on the Internet at 

www.abb.com/knx

 along with the 

corresponding software information

.

 After import into ETS it appears in the 

Catalogs

 window under 

Manufacturers/ABB/Heating Ventilation Air conditioning.

 

The device does not support the locking function of a KNX device in ETS. Using a 

BCU code

 to inhibit 

access to all the project devices has no effect on this device. Data can still be read and programmed. 

 

Summary of Contents for i-bus KNX SUG/U 1.1

























































Reviews:

No comments