ABB i-bus KNX SUG/U 1.1 Page 41 Product Manual Download

Page: 41 / 56

ABB i-bus

KNX

Commissioning

SUG/U 1.1 | 2CDC508171D0201 39

No.

Function

Group object name

Data type

Flags

Status Operating mode

Split unit

1 byte

DPT 20.105

C, R, T

Dependent on parameter

Always visible

This object indicates the operating mode status for the split unit.

0=Auto

1=Heating

3=Cooling

9=Ventilation

14=Drying

Simplified Mode

Split unit

1 bit

DPT 1.100

C, W

Dependent on parameter

Enable "Simplified Mode"

This object switches between heating and cooling for basic applications.

1=Heating

0=Cooling

It is possible to operate the unit in parallel using object 6.

The operating mode status (object 7) is updated.

Silent Mode

Split unit

1 bit

DPT 1.002

C, W

Dependent on parameter

Enable "Silent Mode"

This object activates Silent Mode, provided the split unit supports it.

1=Activate Silent Mode

0=Deactivate Silent Mode

Status Silent Mode

Split unit

1 bit

DPT 1.002

C, R, T

Dependent on parameter

Enable "Silent Mode" and
Enable group object "Status Silent Mode" 1-bit

This object indicates the status of Silent Mode.

1=Silent Mode activated

0=Silent Mode deactivated

Scene

General

1 byte

DPT 18.001

C, W

Dependent on parameter

Enable "Scene" function

Using this 8-bit group object, a Scene telegram can be sent using a coded telegram.

The telegram contains the number of the scene concerned as well as the information on whether the scene is to be recalled or
stored.

The coding for this object is provided in Appendix 1.

Summary of Contents for i-bus KNX SUG/U 1.1

























































Search results

Summary of Contents for i-bus KNX SUG/U 1.1

Reviews:

Related manuals for i-bus KNX SUG/U 1.1

Brands by name

Popular brands

ABB i-bus KNX SUG/U 1.1, Product Manual

Search results

Summary of Contents for i-bus KNX SUG/U 1.1

Reviews:

Related manuals for i-bus KNX SUG/U 1.1

Brands by name

Popular brands