background image

MODBU S EXCEPTIO N CODES

 

TROU BLES HO OTING  

 

56 

 

4JNO0 0030 8 A 

Problem 

Solution 

Device is stuck in handshak-

ing state

 

Reboot the device stuck in handshaking state. If not possible, then reform 

network or power cycle the gateway.

 

Note

: Power cycling the gateway or reforming the network will force all de-

vices to drop off the network and reconnect. This will impact network 

availability.

 

Error Retrieving AP Mote 
Data From Network Manager

 

 

Wait for System Recovery to automatically initiate system recovery. It is of-

ten seen during the boot up process. If this error is persistent after 10+ 

minutes of boot up then a power cycle may be required.

 

Network Manager Has Reset.

 

Wait for System Recovery to automatically initiate system recovery. It is of-

ten seen during the boot up process or during network configuration. If 

this error is persistent after 10+ minutes of boot up then a power cycle 

may be required.

 

8.3

 

Modbus Exception Codes

 

The following exception codes are supported.  

 

Table 16: Exception codes

 

Exception code 

Meaning 

0x01 ILLEGAL_FUNCTION

 

No request bytes present.

 

0x02 ILLEGAL_DATA_ADDRESS

 

Starting address does not exist in mapping.

 

0x03 ILLEGAL_DATA_VALUE

 

 

 

Starting register valid, but length of requests spans at least one un-

mapped register.

 

WirelessHART device is disconnected in simplified in mapping.

 

 

0x06 SLAVE DEVICE BUSY

 

 

 

 

 

Slave is engaged in processing another command. Retry later.

 

This can happen when:

 

 

The data is stale. This can be either because the data is old, or be-
cause the device is responding with a non-successful response 
code. 

 

 

There is an update to the Modbus mapping in progress.

 

 

0x0b GATEWAY TARGET DEVICE 

FAILED TO RESPOND

 

 

 

Indicates that no response was obtained from the target device.

 

This can happen when:

 

 

Device is disconnected.

 

 

Sending request to WirelessHART network failed.

 

 

 

 

To avoid Modbus exception notification, read each individual device data inde-

pendently. In a case of device disconnection, if you try to read data from multi-

ple devices in one block read, it will result in complete Modbus block read error. 

 

Summary of Contents for AWIN GW120













































































Reviews: