ABB AV1 Operating Instructions Manual Download Page 50 | Manualshive

Page: 50 / 126

background image

CALIBRATION

TROUBLESHOOTING CALIBRATION ADJUSTMENTS

4 - 8

TROUBLESHOOTING CALIBRATION ADJUSTMENTS

The I/P converter of the Type AV2 positioner comes from the fac-
tory completely calibrated.

Use the following procedures only

when operating difficulties occur.

The corrective action column

of Table

indicates when to use the troubleshooting calibration.

The purpose of this procedure is to adjust the I/P converter so that
a four to 20-milliamp input signal will produce a 20.7 to 103.4-kilo-
pascal (3.0 to 15.0-pounds per square inch gage) signal. Use the
following procedure to adjust the I/P converter. The supply air
must be connected to the positioner for this procedure.

Tools Required:

•

Digital voltmeter.

•

Calibrated 0 to 30-psig instrument gage.

•

Small screwdriver.

•

Current source.

1. Connect the calibrated zero to 30-psig instrument gage or
other accurate pressure measuring device to the I port to monitor
the signal pressure during calibration.

2. Turn on the supply air to the positioner.

3. Provide a four-mA signal to the I/P converter and observe the
output pressure. If the pressure equals 20.7 kPa (3.0 psig) go to
Step 5. If the pressure does not equal 20.7 kPa (3.0 psig) go to
Step 4.

4. Adjust the zero screw

(→

0

←)

on the bottom of the I/P con-

verter (Fig.

) until the output pressure equals 20.7 kPa (3.0

psig). Clockwise rotation increases pressure.

5. Apply a 20-mA signal to the I/P converter and observe the out-
put pressure. If the pressure equals 103.4 kPa (15.0 psig) go to
Step 7. If the pressure does not equal 103.4 kPa (15.0 psig) go to
Step 6.

6. Adjust the span screw (

⏐↔⏐ )

on the bottom of the I/P con-

verter (Fig.

) until the output pressure equals 103.4 kPa (15.0

psig). Clockwise rotation increases pressure.

7. Repeat Steps 3 through 6 until the 20.7 kPa (3.0 psig) and
103.4 kPa (15.0 psig) outputs are attained with four and 20-mA
signal inputs.

CAUTION

Do not exceed the maximum supply pressure of 1034 kilo-
pascals (150 pounds per square inch gage). Exceeding this
pressure could cause equipment damage.

«
...
48
49
50
51
52
...
»

Summary of Contents for AV1































































































































Reviews:

No comments

Related manuals for AV1

Brand: Samson Pages: 4

Charge Analyzer 711

Brand: 3M Pages: 24

Brand: Banner Pages: 11

Brand: Bante Instruments Pages: 10

Brand: BANTE Pages: 11

Brand: Banner Pages: 14

Brand: Banner Pages: 16

SourceMeter 2400

Brand: Keithley Pages: 594

System SourceMeter 2601B

Brand: Keithley Pages: 864

Brand: Labgear Pages: 8

SourceMeter 2600B Series

Brand: Keithley Pages: 897

Brand: Neogen Pages: 9

Brand: Supertech agroline Pages: 10

Brand: Hanna Instruments Pages: 2

Brand: Zero 88 Pages: 32

Brand: ATIM Pages: 32

Brand: Kobold Pages: 27

Brand: IET Labs Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands