ABB AV1 Operating Instructions Manual Download Page 123

Page: 123 / 126

Index - 3

Index

(continued)

Quick start .................................................................. B-1

Calibration........................................................... B-11
Mounting ............................................................... B-2
Tubing................................................................... B-5
Wiring.................................................................... B-8

Radio frequency interference (RFI) .......................... 3-15
Reference documents ................................................ 1-6
Repeatability............................................................... 1-8
Replacement procedures ........................................... 8-1
Replacing

Cam ...................................................................... 8-5
Diaphragm assembly ............................................ 8-5
Gain hinge spring.................................................. 8-2
I/P assembly ......................................................... 8-4
Manifold ................................................................ 8-1
Pilot valve assembly ............................................. 8-4

Resolution .................................................................. 1-8
Reverse acting ........................................................... 3-6

Short stroking ............................................................. 4-4

Graph.................................................................... 4-5

Single acting actuator tubing connections ...... 3-11, 3-12,
3-13, B-6, B-7
Span adjustment ........................................................ 4-3

Graph.................................................................... 4-5
Short stroking........................................................ 4-4
Split ranging.......................................................... 4-4

Spare parts

Additional .............................................................. 9-3

Specifications

Positioner.............................................................. 1-7

Standard stroke range ..................................... 1-8
Supply pressure .............................................. 1-8
Supply pressure effect..................................... 1-8
Temperature limits........................................... 1-9
Vibration effect ................................................ 1-8
Weight ............................................................. 1-9

Speed.......................................................................... 4-5
Speed adjustment

Orifice .................................................................... 4-6
Pilot valve stroke ................................................... 4-6

Split ranging ................................................................ 4-4

Graph .................................................................... 4-5

Stroke adjustment, pilot valve ..................................... 8-7
Stroke range, standard ............................................... 1-8
Supply pressure .......................................................... 1-8
Supply pressure effect ................................................ 1-8

Temperature limits ...................................................... 1-9
Troubleshooting .......................................................... 6-1

Positioner errors .................................................... 6-1

Troubleshooting calibration......................................... 4-8
Tubing ......................................................................... 3-8

Air supply filtering .................................................. 3-8
Air supply pressure ............................................... 3-8
Air supply quality ................................................... 3-9
Connections .......................................................... 3-9

Double acting actuator .......................... 3-14, B-8
Port locations........................................... 3-9, B-5
Single acting actuator .. 3-11, 3-12, 3-13, B-6, B-7

Unpacking ................................................................... 3-1

Vibration effect ............................................................ 1-8

Weight......................................................................... 1-9
Wiring

AV1 .....................................................................3-13
AV2 .....................................................................3-10
Grounding ...........................................................3-11

Wiring requirements ..................................................3-15

Zero adjustment .......................................................... 4-1

Graph .................................................................... 4-4

Summary of Contents for AV1































































































































Search results

Summary of Contents for AV1

Reviews:

Related manuals for AV1

Brands by name

Popular brands

ABB AV1, Operating Instructions Manual

Search results

Summary of Contents for AV1

Reviews:

Related manuals for AV1

Brands by name

Popular brands