ABB AV1 Operating Instructions Manual Download Page 11 | Manualshive

Page: 11 / 126

background image

INTRODUCTION

APPLICATION

1 - 3

Figures

and

show that the large signal maximum air flow

for both the standard and performance series positioners is about
the same. The performance series positioners achieve maximum
flow capacity at a much smaller error signal.

NOTE:

ABB does not recommend using a performance

series positioner on a small actuator, as it could cause
instability.

Explosionproof I/P Option

The Type AV27 positioner employs an explosionproof I/P con-
verter that is mounted to an adapter block manifold. The adapter
block manifold is bolted to the outside of the main positioner hous-
ing. The unit is a Type AV12 positioner with the electric to pneu-
matic (four to 20-milliamp to 20.7 to 103.4-kilopascal (3.0 to
15.0-pounds per square inch gage)) conversion occurring within
the externally mounted I/P converter.

The four to 20-milliamp input signal wires shall be connected
through an explosionproof conduit entrance on the I/P converter. If
no electrical connections are made within the main housing, the
entire positioner can be considered suitable for application in the
hazardous locations shown on the I/P label.

Refer to Figure

for the external and mounting dimensions of

the Type AV27 positioner.

NEMA 4X Option

The Type AV˘˘˘˘˘˘N positioner comes with a NEMA 4X housing.
To maintain the NEMA 4X classification, the positioner shall be
installed per drawing C258567 and suitable piping shall be
attached to the vent opening and vented in a manner to preclude
the entrance of water under pressure, as from a hose. Addition-
ally, the conduit connections shall be suitable for a NEMA 4X rat-
ing.

APPLICATION

The Type AV1 and Type AV2 Characterizable Pneumatic Position-
ers control the position of a pneumatic actuator.

FEATURES

•

Trouble-Free Operation.

Proven pilot valve that is quickly

removable, provides less downtime, lower maintenance costs,
increased reliability and extended performance.

•

Compact Rugged Design.

Die cast aluminum housing,

beam, spring arm, follower arm and 303 stainless steel pilot

«
...
9
10
11
12
13
...
»

Summary of Contents for AV1































































































































Reviews:

No comments

Related manuals for AV1

Brand: ParTech Pages: 14

Brand: TA Pages: 58

Brand: Dallas Brass Pages: 19

Brand: E Instruments Pages: 2

Brand: Hama Pages: 6

KINGFISHER PLUS+

Brand: semaphore Pages: 247

Brand: OHAUS Pages: 6

Brand: Hanna Instruments Pages: 28

Brand: Kane Pages: 36

Brand: Polimaster Pages: 24

WTW SensoLyt 900

Brand: Xylem Pages: 12

Brand: Milkotester Pages: 44

Brand: Fluke Pages: 5

Brand: PCE Health and Fitness Pages: 4

Brand: madbeanpedals Pages: 2

Brand: VITO Pages: 36

HydroTracer FLV HT2

Brand: aboni Pages: 48

Brand: AEMC Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands