manualshive.com logo in svg

ABB ACS 140, Programming Manual, Page: 50 / 70

Share
Download
ABB ACS 140 Programming Manual Download Page 50

42

Group 22: Accel/Decel

Two acceleration/deceleration ramp pairs can be used. If both ramp pairs are 
used, selection can be made between these in run time through a digital 
input. The S curve of the ramps is adjustable.

Figure 6   Definition of acceleration/deceleration ramp time.

Code Description

2201

ACC/DEC 1/2 SEL
Selects the source for the ramp pair selection signal.

0 = 

NOT

 

SEL

The first ramp pair is used (

ACCELER

 

TIME

 1/

DECELER

 

TIME

 1).

1...5 = DI1...DI5
Ramp pair selection is done through a digital input (DI1 to DI5). 
Digital input deactivated = Ramp pair 1 (

ACCELER

 

TIME

 1/

DECELER

 

TIME

 1) is 

used. 
Digital input activated = Ramp pair 2 (

ACCELER

 

TIME

 2/

DECELER

 

TIME

 2) is used.

2202

ACCELER TIME 1
Ramp 1: time from zero to maximum frequency (0 - 

MAXIMUM

 

FREQ

).

2203

DECELER TIME 1
Ramp 1: time from maximum frequency to zero (

MAXIMUM

 

FREQ

 - 0).

2204

ACCELER TIME 2
Ramp 2: time from zero to maximum frequency (0 - 

MAXIMUM

 

FREQ

).

2205

DECELER TIME 2
Ramp 2: time from maximum frequency to zero (

MAXIMUM

 

FREQ

 - 0).

2206

RAMP SHAPE
Acceleration/deceleration ramp shape selection

0 = 

LINEAR

1 = 

FAST

 

S

 

CURVE

2 = 

MEDIUM

 

CURVE

3 = 

SLOW

 

S

 

CURVE

Output frequency

MAXIMUM

 

FREQ

S curve

Linear

Time

Ramp time

Summary of Contents for ACS 140







































































Reviews:

No comments