manualshive.com logo in svg

ABB ACS 140, Programming Manual, Page: 44 / 70

Share
Download
ABB ACS 140 Programming Manual Download Page 44

36

Group 13: Analogue Inputs

Code Description

1301

MINIMUM AI1
Relative minimum value of AI1 (%). Value corresponds to minimum reference 
set by parameter 1104 

EXT

 

REF

1 

MIN

 or 1107 

EXT

 

REF

2 

MIN

.

See Figure 3 on page 34.

1302

MAXIMUM AI1
Maximum value of AI1 (%). Value corresponds to maximum reference set by 
parameter 1105 

EXT

 

REF

1 

MAX

 or 1108 

EXT

 

REF

2 

MAX

.

See Figure 3 on page 34.

1303

FILTER AI1
Filter time constant for analogue input AI1. As the analogue input value 
changes, 63 % of the change takes place within the time specified by this 
parameter. 

Note! Even if you select 0 s for the filter time constant, the signal is still filtered 
with a time constant of 0.1 ms due to the signal interface hardware. This cannot 
be changed by any parameters.

Figure 4   Filter time constant for analogue input AI1.

1304

MINIMUM AI2
Minimum value of AI2 (%). Value corresponds to minimum reference set by 
parameter 1104 

EXT

 

REF

1 

MIN

 or 1107 

EXT

 

REF

2 

MIN

.

1305

MAXIMUM AI2
Maximum value of AI2 (%). Value corresponds to maximum reference set by 
parameter 1105 

EXT

 

REF

1 

MAX

 or 1108 

EXT

 

REF

2 

MAX

.

1306

FILTER AI2
Filter time constant for AI2. Refer to parameter 1303 

FILTER

 

AI

1.

63

[%]

100

Time constant

t

Filtered Signal

Unfiltered Signal

Summary of Contents for ACS 140







































































Reviews:

No comments