manualshive.com logo in svg

ABB ACH550-UH HVAC, Installation, Operation & Maintenance Manual

Share
Download
ABB ACH550-UH HVAC Installation, Operation & Maintenance Manual Download Page 69

ACH550 Installation, Operation and Maintenance Manual

69

ACH550 E-Clipse Bypass

3018

MAX CYCLE 

FAULT

Supervisory Mode only. 

Declared if bypass 

contactor is closed by 

supervisory control 16 

times within a 1 hour 

period.

High and low levels of 

hysteresis band are too 

tight 

Check parameters 

3202-3205. Increase 

time delays on 

parameters 3204 and 

3205

3019

DRIVE LINK FAULT Supervisory Mode 

Only. Fault generated if 

RS-485 link between 

drive and bypass stops 

communicating.

Bad cable/connection 

between drive and 

bypass.
Communication 

improperly set in drive 

Parameter 9802. 

Application Macro 

improperly set in drive 

parameter 9902.

Proper seating of cable 

in drive and 

RBCU(connector J3)
Check drive parameter 

9802 (Modbus) and 

9902 (E-Clipse)
Check drive Group 53 
Follow DriveLink 

recovery procedure

3020

PHASE SEQ

Sequence of 3 phase 

voltage input is such 

that bypass operation 

will result in motor 

rotation opposite of 

drive forward operation.

Phase sequence 

unknown at time of 

wiring

Swap any two of the 

three input wires to the 

bypass unit

3021

PH A CURR FBK

Fault is generated 

when current in Phase 

A  is detected and the 

bypass contactor is 

open

Loose CT connection
Bad RBCU
Bad CT

Check J2 connector for 

proper seating
Check connector on 

Current Assembly
Replace RBCU
Replace RCSA unit

3022

PH C CURR FBK

Fault is generated 

when current in Phase 

C  is detected and the 

bypass contactor is 

open

Loose CT connection
Bad RBCU
Bad CT

Check J2 connector for 

proper seating
Check connector on 

Current Assembly
Replace RBCU
Replace RCSA unit

3023

BYP COIL 

SHORTED

Coil characteristics are 

checked only on power 

up and coil current is 

greater than allowable 

values

Shorted contactor coil
Shorted/damaged 

cable
Bad RBCU

Replace RBCU
Replace RCSA unit

3024

DRV COIL 

SHORTED

Coil characteristics are 

checked only on power 

up and coil current is 

greater than allowable 

values

Shorted contactor coil
Shorted/damaged 

cable
Bad RBCU

Replace RBCU
Replace RCSA unit

3027

INVALID SUB ASM

Contactor assembly as 

recorded in the RBCU 

unit does not match 

drive information 

communicated via 485 

link

RBCU unit from a 

different size bypass 

used to replace a 

defective RBCU.
Parameters not 

matched after 

Firmware change.

Contact ABB at 

1-800-HELP-365 

Option 4

Fault 

Code

Fault Name In 

Panel

Fault

Possible Cause

Corrective Action

Summary of Contents for ACH550-UH HVAC































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands