manualshive.com logo in svg

ABB ACH550-UH HVAC, Installation, Operation & Maintenance Manual

Share
Download
ABB ACH550-UH HVAC Installation, Operation & Maintenance Manual Download Page 27

ACH550 Installation, Operation and Maintenance Manual

27

ACH550-UH

35

OUTPUT

 

WIRING

Possible power wiring error detected. When the drive is not running it 

monitors for an improper connection between the drive input power and the 

drive output. Check for and correct:

• Proper input wiring – line voltageis NOT connected to drive output.
• The fault can be erroneously declared if the input power is a delta 

grounded system and motor cable capacitance is large. This fault can be 

disabled using parameter 3023 

WIRING

 

FAULT

.

36

INCOMP

 

SWTYPE

The drive cannot use the software.
• Internal Fault.
• The loaded software is not compatible with the drive. 
• Call support representative.

37

CB OVERTEMP

Drive control board is overheated.

Check for and correct:
• Excessive ambient temperatures
• Fan failure.
• Obstructions in the air flow.

38

USER

 

LOAD

 

CURVE

Condition defined by parameter 3701 USER LOAD C MODE has been valid 

longer than the time defined by 3703 USER LOAD C TIME.

101

SERF

 

CORRUPT

  Error internal to the drive. Contact your local ABB sales representative and 

report the error number.

102

RESERVED

103 

SERF

 

MACRO

 

104 

RESERVED

105

RESERVED

201

DSP

 

T

1 

OVERLOAD

 

Error in the system. Contact your local ABB sales representative and report 

the error number.

202 

DSP

 

T

2 

OVERLOAD

 

203

DSP

 

T

3 

OVERLOAD

 

204 

DSP

 

STACK

 

ERROR

 

205

RESERVED

(obsolete)

206

OMIO

 

ID

 

ERROR

 

207

EFB

 

LOAD

 

ERR

1000

PAR

 

HZRPM

 

LIMITS

Parameter values are inconsistent. Check for any of the following:
• 2001 

MINIMUM

 

SPEED

 > 2002 

MAXIMUM

 

SPEED

.

• 2007 

MINIMUM

 

FREQ

 > 2008 

MAXIMUM

 

FREQ

.

• 2001 

MINIMUM

 

SPEED

 / 9908 

MOTOR

 

NOM

 

SPEED

 is outside proper range 

(> 50)

• 2002 

MAXIMUM

 

SPEED

 / 9908 

MOTOR

 

NOM

 

SPEED

 is outside proper range 

(> 50)

• 2007 

MINIMUM

 

FREQ

 / 9907 

MOTOR

 

NOM

 

FREQ

 is outside proper range 

(> 50)

• 2008 

MAXIMUM

 

FREQ

 / 9907 

MOTOR

 

NOM

 

FREQ

 is outside proper range 

(> 50)

1001

PAR

 

PFAREFNG

 

Parameter values are inconsistent. Check for the following:
• 2007 

MINIMUM

 

FREQ

 is negative, when 8123 

PFA

 

ENABLE

 is active.

Fault 

Code

Fault Name In 

Panel

Description and Recommended Corrective Action

Summary of Contents for ACH550-UH HVAC































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands