ABB A175-M66 Operating Manual Download Page 44 | Manualshive

Page: 44 / 150

background image

Operation Manual / A170-M.. - A175-M..

5 Monitoring during operation / 5.1 Oil pressure, oil temperature

© Copyright 2021 ABB. All rights reserved.

HZTL4033_EN

Rev.H

July 2021

Lubricating oil temperature at the inlet

CAUTION

Machine damage

If the oil temperature at the oil inlet exceeds the admissible range, this may
lead to engine damage.

u

Observe oil temperature at the oil inlet according to the following table.

Status for operation

Oil temperature at the inlet

T

oil,inlet

[°C]

Admissible

< 90

Temporarily admissible (< 1 h)

→

alarm

> 90

Not admissible

→

stop engine

> 95

Table 11: Oil temperature at the inlet

Lubricating oil temperature at the outlet

The oil temperature at the outlet is mainly dependant on:

¡

Lubricating oil temperature and pressure at the oil inlet

¡

Engine load and turbocharger speed

¡

Exhaust gas temperature

The maximum admissible oil temperature at the outlet is listed in the following table. The
specified oil outlet temperature is to be considered as alarm value for the turbocharger op-
eration and must be monitored according to the current regulations.

Status for operation

Oil temperature at the outlet

T

oil,outlet

[°C]

Admissible

≤

135

Temporarily admissible

→

alarm

> 135

Not admissible

→

stop engine

> 155

Table 12: Oil temperature at the outlet

If the turbocharger has been operated for a longer period of time outside the admissible
range, ABB Turbocharging recommends having the turbocharger inspected by an ABB Tur-
bocharging Service Station.

Page

42

/

147

«
...
42
43
44
45
46
...
»

Summary of Contents for A175-M66























































































































































Reviews:

No comments

Related manuals for A175-M66

Brand: Zenoah Pages: 20

Brand: Avco Lycoming Pages: 110

Brand: Westerbeke Pages: 2

10.0 KW-60Hz SBEG

Brand: Westerbeke Pages: 104

Brand: Baumer Hübner Pages: 20

Brand: Briggs & Stratton Pages: 60

Brand: YS Pages: 2

Brand: Fanotec Pages: 2

Brand: O.S. Speed Pages: 4

Brand: Honda Pages: 431

Brand: Erfal Pages: 8

Brand: DLE Pages: 4

Brand: LinMot Pages: 48

Brand: Beamz Pages: 6

Brand: Mitsubishi Pages: 16

Brand: SKY Engines Pages: 39

Brand: HandI Move Pages: 26

Brand: Nanni Pages: 175

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands