ABB A175-M66 Operating Manual Download Page 104

Page: 104 / 150

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.10 Fitting the spinner nose cone

HZTL4033_EN

Rev.H

July 2021

9.10

Fitting the spinner nose cone

If present:

The spinner nose cone (25012) and Loctite®542 are supplied by the ABB service station to-
gether with the overhauled cartridge group.

CAUTION

Total failure of turbocharger

If the spinner nose cone (25012) is not fitted correctly, or the socket screw
(25013) is not correctly tightened, the spinner nose cone can work loose dur-
ing operation and cause total failure of the turbocharger.

Follow the assembly instructions.

Always use a new socket screw (25013) and washer (25014) from the cus-
tomer spare part set (97070).

Only use new Loctite®542 supplied by the ABB service station.

Observe and note down control dimension Z.

Fig. 58: Preparing the threaded stud (25008)

Product

Size

A170-M

A175-M

M10

Table 42: Inner thread size (25008)

1. Remove residual glue from the inner thread of the threaded stud (25008) by using a

screw tap.

Page

102

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operating Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands