ABB A175-M66 Operating Manual Download Page 38

Page: 38 / 150

Operation Manual / A170-M.. - A175-M..

3 Removal and installation / 3.3 Installing the turbocharger

HZTL4033_EN

Rev.H

July 2021

3.3.1

Tightening the clamping nut

Preparation for tightening

CAUTION

Do not clean pressure screws (d)

The pressure screws are equipped with a permanent sliding layer that must
not be removed.

Do neither clean nor lubricate the pressure screws. In case of non-compli-
ance, it cannot be ensured that the necessary tension force is reached.

Do not clean pressure screws.

Do not lubricate pressure screws.

NOTICE

Pressure screws (d) must not protrude from the clamping nut (c) in the dir-
ection of the thrust washer (b)

In order to correctly fit the clamping nuts, the pressure screws must not
protrude in the direction of the thrust washer.

Fig. 21: Tightening the foot screws (1)

1. Clean the bolt thread (a) and the contact surface.

Coat the bolt thread with grease.

2. Fit thrust washer (b) (component of clamping nut).

3. Tighten clamping nut (c) by hand.

4. Screw back clamping nut by ¼ of a turn (90°).

The distance between the thrust washer and the clamping nut is now about 1 mm.

Page

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operating Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands