ABB A175-M66 Operating Manual Download Page 126

Page: 126 / 150

Operation Manual / A170-M.. - A175-M..

10 Taking a turbocharger out of operation / 10.3 Fitting the cover plate

HZTL4033_EN

Rev.H

July 2021

Fig. 76: Fitting the cover plate

1. Remove the cartridge group (see chapter Disassembly and assembly / Removing the

cartridge group).

2. Close the opening in the gas outlet casing with the cover plate (01).

3. Attach cover plate with spacer sleeves (02) and nuts (61037).

Close the lubricating oil supply to the turbocharger.

10.3.1

Further measures and information for the operation of
4-stroke engines with a cover plate of the turbocharger

4-stroke engine with a turbocharger

No further measures are necessary. The engine can be operated as a suction engine accord-
ing to the instructions of the enginebuilder.

4-stroke engine with several turbochargers

Separate receivers

In engines with separate air and exhaust gas receivers, no further measures are necessary.
The engine can be operated as a suction engine according to the instructions of the en-
ginebuilder.

Page

124

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operating Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands