ABB A175-M66 Operating Manual Download Page 78

Page: 78 / 150

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.1 Introduction

HZTL4033_EN

Rev.H

July 2021

Disassembly and assembly

9.1

Introduction

CAUTION

Further work

This Operation Manual may be used to carry out only the work described in
it. Further work that is carried out in an incorrect way can lead to serious
damage to the machine.

ABB Turbocharging recommends having further work carried out only by
trained personnel from an ABB Turbocharging Service Station.

Mark the casing position for assembly.

Customer tool set

Before starting work, make sure the required tool set is available (see chapter

Tools

→

142

Not all tools are marked with a part number. Identification is guaranteed by the tool list. This
list is enclosed with the tool set.

WARNING

Servicing the tools

The tools must be checked for damage before and after use.

Visually inspect for corrosion, cracks, deformation and wear.

Damaged tools must no longer be used and must be replaced.

Customer spare part set

Before starting work, make sure the required customer spare part set is available (see
chapter

Spare parts

→

130

Tightening torques for components

The specified tightening torques of the bolted connections must be observed.

Tightening torques for assembly devices

Unless otherwise described, the screws and nuts of the assembly devices supplied by ABB
must be tightened in such a way that they are tight-fitting.

Page

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operating Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands