ABB A175-M66 Operating Manual Download Page 35

Page: 35 / 150

Operation Manual / A170-M.. - A175-M..

3 Removal and installation / 3.3 Installing the turbocharger

HZTL4033_EN

Rev.H

July 2021

Removing auxiliary screws

Fig. 16: Removing auxiliary screw

Remove shipping screws (90334 / 90335) on the left and right side of the foot and place
in the toolbox.

The turbocharger is delivered with a pre-installed sliding block (68003). The shipping screws
secure the sliding block in the preset position. In operation, the foot can slip due to thermal
expansion.

Tighten clamping nuts as described in the following sections.

Connect all gas, air and oil pipes.

If present: Re-fit the insulation segments.

If present: Connect cable to speed sensor.

Compressor-end (CE) foot

Fig. 17: Compressor-end foot

Page

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operating Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands