ABACO VMIVME-1184 Series Hardware Reference Manual Download Page 37

Page: 37 / 46

36 VMIVME-1184* 32-bit Optically Isolated Change-of-State (COS) Input Board

Publication No. 500-001184-000 Rev. B.0

• Counter_Value

• PREV_Input_Data

• COS_Input_Data

Figure 3-1 COS and SOE Registers

3.7.1 Counter Register (Offset: $XXXX14)

This register contains the current count derived from the front panel input (P3).
The Counter register is a longword read/write register, so the user can begin the
count with a predetermined value by writing directly to the register.

3.7.2 COS SEL B/A

Channel x

These bits work as a pair for the stated channel. They define the COS trigger
condition for the associated channel. Their states and functions are:

Example:

Setting Bits 15 and 14 of address $XXXX1E will cause a COS trigger on any edge
occurrence for channel 7.

Table 3-9 COS SEL B/A

B/A

Function

No interrupts (data only)

Rising edge interrupts only

Falling edge interrupts only

Any edge interrupt

COS

SOE

Read COS

Counter

0x10

Data

0x08

Counter

0x10

Data

0x08

Read 1C

Read 1F

Read SOE

Read 1C

Read 1P

Read 1F

C = Counter

F = Flagged

P = Previous

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for VMIVME-1184 Series















































Search results

Summary of Contents for VMIVME-1184 Series

Reviews:

Related manuals for VMIVME-1184 Series

Brands by name

Popular brands

ABACO VMIVME-1184 Series, Hardware Reference Manual

Search results

Summary of Contents for VMIVME-1184 Series

Reviews:

Related manuals for VMIVME-1184 Series

Brands by name

Popular brands