Aanderaa 4330 Operating Manual Download Page 55

Page: 55 / 93

TD 269 OPERATING MANUAL

OXYGEN OPTODE 4330, 4831, 4835

June 2017

page 55 of 93

Later it has been shown by Craig Neill (CSIRO) that this formula generally performs better with

respect to interpolation between calibration points and extrapolation outside the calibration

range. Based on this and recommendation from the Argo oxygen meeting in Brest 2011 the

above formula has been implemented in the Optode firmware (serial no. 1000 and above).

In order to use the “Stern-Volmer-Uchida” formula the property called

Enable SVUformula

must be set to

‘yes’. The coefficients c

to c

are stored in the

SVUFoilCoef

property.

A possibility for linear correction of the O

concentration was also introduced:

𝐎𝐎𝟐𝟐𝐎𝐎𝐎𝐎𝐎𝐎𝐜𝐜𝐎𝐎𝐎𝐎𝐎𝐎𝐎𝐎𝐎𝐎𝐎𝐎𝐎𝐎𝐎𝐎𝐎𝐎

[

𝐮𝐮𝐮𝐮

] =

𝐎𝐎𝐎𝐎𝐎𝐎𝐜𝐜𝐎𝐎𝐎𝐎𝐎𝐎𝐨𝐨

𝟎𝟎

𝐎𝐎𝐎𝐎𝐎𝐎𝐜𝐜𝐎𝐎𝐎𝐎𝐎𝐎𝐨𝐨

𝟏𝟏

[

𝐎𝐎

𝟐𝟐

]

′

For new Optodes (serial no. 1000 and above) the two-point calibration procedure (ref

Calibration Procedure chapter 6.2.2 ) will adjust the

ConcCoef

coefficients.

Summary of Contents for 4330






























































































Search results

Summary of Contents for 4330

Reviews:

Brands by name

Popular brands

Aanderaa 4330, Operating Manual

Search results

Summary of Contents for 4330

Reviews:

Brands by name

Popular brands