Aanderaa 4330 Operating Manual Download Page 2

Page: 2 / 93

TD 269 OPERATING MANUAL

OXYGEN OPTODE 4330, 4831, 4835

June 2017

page 2 of 93

Edition

February 2008 PRELIMINARY

Edition

October 2008

Edition

February 2009 Including description of Optode 4835

Edition

August 2013, Including general updates in text, list of scientific publications, description of

Optode, Frame Work 3 update, description of Optode 4831, multipoint calibration with

improved accuracy and artificial oxygen consumption by sacrificial anode, updated FAQ,

Rebranded.

Edition

February 2014 Updated text on page 17, 54 and 55

Edition

September 2015 Correction in formula page 56

Edition

June 2017 New foil Kit 5551 added

NOTE! The latest version of the FAQ for the Oxygen Optodes is available on our web site.

Contact information:

Aanderaa Data Instruments AS
PO BOX 34, Slåtthaug
5851 Bergen, NORWAY

Visitor address:
Nesttunbrekken 97
5221 Nesttun, Norway

TEL: +47 55 604800

E-MAIL

[email protected]

WEB

http://www.aanderaa.com

Summary of Contents for 4330






























































































Search results

Summary of Contents for 4330

Reviews:

Brands by name

Popular brands

Aanderaa 4330, Operating Manual

Search results

Summary of Contents for 4330

Reviews:

Brands by name

Popular brands