Aanderaa 4330 Operating Manual Download Page 37

Page: 37 / 93

TD 269 OPERATING MANUAL

OXYGEN OPTODE 4330, 4831, 4835

June 2017

page 37 of 93

6.1 Changing the Sensor Foil

If the sensor foil gets damaged it can easily be changed. For the 4330 and the 4831 models it is possible

to change between the standard foil and fast response foil. The

Sensor Foil Kit 4733

for Optode 4330,

4831 and 4835 and Semnsor Foil Kit 5551 for Optode 5551 contains 1 standard foils while

Sensor Foil Kit

4794

for Optode 4330 and 4831

contains 1 fast response foils. The content of Kit 4733/4794/5551 is

given in Table 6-1, and a procedure for changing the foil is given below the table.

NOTE! If you use a foil from a different batch, new foil coefficients must be entered.

NOTE! After changing the foil and entering new foil coefficients a new two or multipoint calibration should

be performed (see below).

Table 6-1 Contents of Sensor Foil Kit 4733/4794/5551

Part no.

Pieces

Description

Foil Kit

4733

Foil Kit

4794

Foil Kit

5551

1206005A

Standard Sensing Foil packed in

aluminium foil

1206020

Fast Response Sensing Foil packed

in aluminium foil

1206019

Standard Sensing Foil packed in

aluminium foil

1913042

Torx key no. T9

1642223

M3 x 6mm screw torx a4 Din 965a

(4330/4831)

1642222

M2.5 x 6mm screw torx a4 Din 965a

(4835)

Form No. 721

Calibration Sheet for Sensing Foil (each batch of

foils is calibrated)

Summary of Contents for 4330






























































































Search results

Summary of Contents for 4330

Reviews:

Brands by name

Popular brands

Aanderaa 4330, Operating Manual

Search results

Summary of Contents for 4330

Reviews:

Brands by name

Popular brands