background image

 

3

1. INTRODUCTION 

This manual describes how the SV-A/SV-H series viscometer works and how to get the most out of it 
in terms of performance.   

Read this manual thoroughly before using the viscometer and keep it at hand for future reference. 
The SV-A series uses a stand. In a laboratory, quality control room etc, you can make accurate 

measurements using the stand set, the sample cup set and the software set provided. 

The SV-H series uses a handle only. While at a manufacturing location, you can make a 

measurement easily. If you buy the accessories, the SV-H series functions the same as the SV-A 

series. 

 

1-1 Compliance 

Compliance with FCC Rules 

Please note that this device generates, uses and can radiate radio frequency energy. This 
device has been tested and has been found to comply with the limits of a Class A computing 
device pursuant to Subpart J of Part 15 of FCC rules. These rules are designed to provide 
reasonable protection against interference when this device is operated in a commercial 
environment. If this unit is operated in a residential area, it may cause some interference and 
under these circumstances the user would be required to take, at his own expense, whatever 
measures are necessary to eliminate the interference. 

(FCC = Federal Communications Commission in the U.S.A.) 

 

Compliance with Council Directives

 

 

This device features radio interference suppression and safety regulation in compliance with 
the following Council Directives 

 

    Council directive 89/336/EEC 

EN61326 

EMC directive 

 

    Council directive 73/23/EEC 

EN60950 

Safety of Information Technology Equipment

 

 
 

EN61326  Emission and Immunity. 
 

 

Note 

The CE mark is an official mandatory European marking.   
Please note that any electronic product must comply with local laws and regulations when 
sold or used anywhere outside Europe.

 

 

 

 

 

 

 

 

Summary of Contents for SV-1A







































































































Reviews: