A&D GX-M Series Instruction Manual Download Page 5

Page: 5 / 24

RS-232C/USB board

ケーブル

Rubber

packing

ネジ

ロック付きコネクタ

Packing List

GXM

04 ................ Mini DIN connector (8 pin, plug)

Cable with connector (AX-KO5692)

This manual

GXA-06 .................. Screwdriver for adjustment

Mini DIN connector (4 pin, plug)

Cable with connector (AX-KO5692)

This manual

Installing the Option

Caution

Disconnect the AC adaptor before installing the option to the balance.

Installing the option board to the balance

Install the GXM-04 and GXM-06 according to the following procedure.

(The installation procedure of the GXM-04 and GXM-06 is the same.)

Step1 Remove the two screws from the panel and remove the

RS-232C / USB board from the balance.

Step2 Pull gently and remove the two cables from

the RS-232C / USB board.

Step3 Insert the two cables into the sockets of the GXM-06 board.

Step4 Insert the rubber packing and plug the GXM-06

into

the

balance.

Screw the panel of GXM-06.

Caution

When inserting the GXM-06, pay attention to the top and bottom orientation of the board.

The rubber packing has a deep groove on the balance side.

Rubber packing

Connector

Cable

Screw

Connector with lock

Step1

Step2

Step3

Step4

GXM-06 board

Summary of Contents for GX-M Series

























Search results

Summary of Contents for GX-M Series

Reviews:

Related manuals for GX-M Series

Brands by name

Popular brands

A&D GX-M Series, Instruction Manual

Search results

Summary of Contents for GX-M Series

Reviews:

Related manuals for GX-M Series

Brands by name

Popular brands