A.O. Smith Innovo IR 12-160 Installation, User And Service Manual Download Page 73

Page: 73 / 96

Indication

Cause

Measure

value (at full load)

is not correct

The unit is not set for the correct gas
type

Make sure that the gas type
corresponds with the information on
the rating plate

Make sure if the venturi restrictor has
the correct diameter, refer to Gas
details.

Contaminated venturi

Remove any contamination from the venturi
inlet.

Leakage between venturi and flexible
venturi connector

Make sure that the flexible venturi
connector is not damaged.
If necessary replace the flexible
venturi connector

Make sure that the flexible venturi
connector is correctly connected.
If necessary, tighten the clamp.

Recirculation of flue gases

Make sure that the CO

-value

measured in the flue gas outlet is
correct, refer to CO

value (see 8.9.4).

Make sure that the CO

value

measured in the air inlet is below
0.5 vol%.

If necessary, reconnect the venting
system and change the necessary
seals.

0312266_INNOVO_UKUK_

V5.1, 2022-07-12

Summary of Contents for Innovo IR 12-160

































































































Search results

Summary of Contents for Innovo IR 12-160

Reviews:

Related manuals for Innovo IR 12-160

Brands by name

Popular brands

A.O. Smith Innovo IR 12-160, Installation, User And Service Manual

Search results

Summary of Contents for Innovo IR 12-160

Reviews:

Related manuals for Innovo IR 12-160

Brands by name

Popular brands