A.O. Smith Innovo IR 12-160 Installation, User And Service Manual Download Page 26

Page: 26 / 96

Note
If the water heater is in OFF mode for more than 2 months and no water is drained, air
bubbles may be formed in the water heater. This can lead to air in the water pipes.

4.3.2

Isolate from the mains

To isolate the water heater from the mains:
1.

Set parameter

001

OFF

, refer to Set a parameter value (see 4.1).

Wait 1 minute to make sure that the water heater stopped operating.

Set the control switch to 0.

Disconnect the water heater from the mains by turning the isolator.

4.3.3

Turn off for a long period

When the water heater needs to be turned off for more than 2 months, contact your
service and maintenance engineer to decommission the water heater.

User part

Summary of Contents for Innovo IR 12-160

































































































Search results

Summary of Contents for Innovo IR 12-160

Reviews:

Related manuals for Innovo IR 12-160

Brands by name

Popular brands

A.O. Smith Innovo IR 12-160, Installation, User And Service Manual

Search results

Summary of Contents for Innovo IR 12-160

Reviews:

Related manuals for Innovo IR 12-160

Brands by name

Popular brands