20
7-INSTALLATION
(continued)
2014 June
7000a-7000a3 Pro - NA
7.7 Completion of Taping Heads
See Manual 2 or 3 for Complete Instructions:
1. Place the Upper Taping Head in a convenient
working
position
2. Use
Figure 7-8
and tape threading label. Position
the tape supply roll so the adhesive side of tape is
facing the front of the taping head as it is pulled
from the supply roll.
3. Attach the threading needle to the end of the roll.
Guide the threading needle around the wrap roller
(Position 1)
then back around the one-way tension
roller
(Position 2).
4. Continue pulling the threading needle down and
guide it between the two (2) rollers on the apply
arm
(Position 3).
5. Pull the threading needle down until the tape travels
between the apply plate and the ears of the apply
arm
(Position 4)
until it extends past the applying
roller. When properly threaded the adhesive side of
the tape should be facing the knurled rollers at
position 2 and also position 3.
6. Cut away any excess tape and repeat steps for
Lower Taping Head.
Important –
Do not cut against the apply roller -
roller damage could occur.
7.9.2
Check that the connection of the machine to the
mains meets the safety regulations in your country.
7.9.3
The machine is
fi
tted with a main switch and a
circuit breaker. The user should check that the
electrical settings of the machine are compatible
with all the components of the mains system.
7.10 Machine Connection to the Mains
For technical speci
fi
cations:
See Section 4 -
Specif
i
cations
- Push the LATCHING EMERGENCY STOP BUTTON.
- The main switch is normally turned OFF (O).
Connect the power cord supplied with the machine to a
wall socket using a plug which complies with the safety
regulations of your country.
One Way
Tension
Roller
Tension
Wrap
Roller
Knurled
Roller
Wrap
Roller
Applying
Roller
Threading
Needle
#1
#2
#3
#4
Figure 7-8
Figure 7-9
7.8 Outboard Tape Roll Holder
If you intend to use the outboard tape roll holder,
proceed as follows:
1. Remove the lower taping head from the machine.
2. Remove the tape drum bracket assembly, stud
spacer, and fasteners from the lower taping head.
3. Install alternative wrap roller and bracket on the
head in place of tape bracket. Replace lower
head into machine.
4. Install and secure tape drum bracket assembly
on the entry end of the lower frame
(as shown in
Figure 7-9).
7.9 Preliminary Electric Inspection
Before connecting the machine to the mains please
carry out the following operations:
7.9.1
Make sure that the socket is provided with an
earth protection circuit and that both the mains
voltage and the frequency match the speci
fi
ca-
tions on the name plate.
Summary of Contents for Matic 7000a
