3M Bair paws 875 Service Manual Download Page 9

Page: 9 / 33

English 202036A

Check the 3M

Bair Paws

system website to ensure you have the most recent version of this document.

www.bairpaws.com reorder #202036A

7�

To reduce the risks associated with fire:

• Always follow standard safety protocols when using high intensity heat sources near a

Bair Paws gown�

CAUTION:

1�

To reduce the risks associated with impact or property damage:

• Initiate patient warming only after the warming unit is safely placed on a hard surface

or securely mounted�

2�

To reduce the risks associated with environmental contamination:

• Follow applicable regulations when disposing of this device or any of its electronic

components�

3�

To reduce the risks associated with thermal energy:

• Do not cut the gown, and do not connect the gown to a warming unit if the fabric is

torn or cut; air channels could be damaged�

• Avoid rolling, gathering, bunching or compressing the air-channel insert of the gown

as this can occlude airflow and reduce warming of the patient� Extend the insert to its

full length for optimal heat transfer when connected to a warming unit�

4�

To reduce the risk associated with impact or tripping:

• Do not use the Bair Paws pediatric gown unless the patient is over 102 cm (40 inches)

tall�

5�

To reduce the risks associated with pinching or device damage of the suction wall

mount adapter:

• Only hold the front of the adapter when increasing/decreasing the expander�
• Overtorquing the suction wall mount adapter may cause device damage�

NOTICE:

1�

The Bair Paws warming unit meets the international electronic interference

requirements� If radio frequency interference with monitoring equipment occurs,

connect the warming unit to a different power source�

2�

Federal law (USA) restricts this device to sale by or on the order of a licensed healthcare

professional�

3�

Do not place the warming unit on a soft or uneven surface, such as a bed; this may

cause the air intake to become blocked, compromising the unit’s performance�

4�

Do not immerse any part of the Bair Paws warming unit in liquid while cleaning it�

5�

Do not use a dripping wet cloth to clean the warming unit�

6�

Do not use harsh solvents to clean the warming unit�

7�

To the full extent permitted by law, the manufacturer and/or importer declines all

responsibility for thermal injury resulting from the unit being used in conjunction with

products other than Bair Paws warming gowns�

Summary of Contents for Bair paws 875


































Search results

Summary of Contents for Bair paws 875

Reviews:

Related manuals for Bair paws 875

Brands by name

Popular brands

3M Bair paws 875, Service Manual

Search results

Summary of Contents for Bair paws 875

Reviews:

Related manuals for Bair paws 875

Brands by name

Popular brands