3M Bair paws 875 Service Manual Download Page 7

Page: 7 / 33

English 202036A

Check the 3M

Bair Paws

system website to ensure you have the most recent version of this document.

www.bairpaws.com reorder #202036A

Manufacturer

This system is subject to European WEEE Directive 2002/96/EC�

This product contains electrical and electronic components and must

not be disposed of using standard refuse collection� Please consult local

directives for disposal of electrical and electronic equipment�

Consult instructions for use

Follow instructions for use

Recycle to avoid environmental contamination� This product contains

recyclable parts� For information on recycling, please contact your nearest

3M Service Center for advice�

Keep dry

Temperature limit

Explanation of Signal Word Consequences

WARNING:

Indicates a hazardous situation which, if not avoided, could result in death or serious injury�

CAUTION:

Indicates a hazardous situation which, if not avoided, could result in minor or moderate

injury�

NOTICE:

Indicates a situation which, if not avoided, could result in property damage only�

Contraindication

To reduce the risks associated with thermal energy:

•

Do not apply heat to lower extremities during aortic cross-clamping as thermal injury

may occur if heat is applied to ischemic limbs�

WARNING:

1�

Do not use a forced-air warming device over transdermal medications; increased drug

delivery, patient death, or injury may occur�

2�

To reduce the risks associated with thermal energy hazards:

• Do not continue use of the unit if the yellow Over-temp indicator light illuminates

or an audible alarm sounds; contact a biomedical technician or call 3M Patient

Warming technical service�

• Use only the Bair Paws warming gowns with this warming unit�
•

Do not warm patients with the warming unit’s hose alone�

Always connect the hose to a Bair Paws warming gown before providing

patient warming�

Summary of Contents for Bair paws 875


































Search results

Summary of Contents for Bair paws 875

Reviews:

Related manuals for Bair paws 875

Brands by name

Popular brands

3M Bair paws 875, Service Manual

Search results

Summary of Contents for Bair paws 875

Reviews:

Related manuals for Bair paws 875

Brands by name

Popular brands