manualshive.com logo in svg

3DHISTECH TMA Grand Master 2.6, User Manual

Share
Download
3DHISTECH TMA Grand Master 2.6 User Manual Download Page 34

TMA Grand Master 2.6 – User’s Guide

4 Operating the Main Unit

5. Hold the front cog wheel firmly and loosen the rear cog wheel (marked with red) and turn it 

anticlockwise about two turns (360-720 degrees), then remove the drill bit from the drill 
chuck.

Figure 9 – Drill chuck

6. Insert the drill bit you want to use into the drill chuck, and push it inwards as much as you 

can.

7. Hold the front cog wheel firmly and tighten the rear cog wheel (clockwise). Make sure with 

the help of the tool that the upper cog wheel is secured firmly.

8. Insert the drill chuck into its position and fix it with the locking lever. Ensure that the two cog 

wheels (motor and drill chuck) are aligned exactly.

9. Loosen the puncher chuck locking lever that keeps the puncher chuck in position

 

and remove 

the puncher chuck assembled with the piston.

       

Figure 10 – Removing the puncher chuck

December 9, 2016 – Rev. 1

3DHISTECH Ltd.

34(92)

Summary of Contents for TMA Grand Master 2.6





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands