3Com U.S. Robotics 56K Voice User Manual Download Page 35

Page: 35 / 168

Adding TCP/IP to Your Protocols List

The Select Network Protocol dialog box appears.

Figure 18

Select Network Protocol Dialog Box

From the Manufacturers list box, select

Microsoft

, and then from the Network

Protocols list box, select

TCP/IP

Click

to exit the Select Network Protocol Dialog box.

Click

again to exit the Network Dialog box.

You may be prompted to re-boot your workstation.

Run the EZ-LAN Wizard again to optimize the settings on your workstation.

Windows NT 4.0

To add TCP/IP to your protocols list for Windows NT 4.0:

You may need your Windows NT 4.0 installation CD-ROM.

From the Control Panel, double-click

Network

The Network dialog box appears.

Summary of Contents for U.S. Robotics 56K Voice









































































































































































Search results

Summary of Contents for U.S. Robotics 56K Voice

Reviews:

Related manuals for U.S. Robotics 56K Voice

Brands by name

Popular brands

3Com U.S. Robotics 56K Voice, User Manual

Search results

Summary of Contents for U.S. Robotics 56K Voice

Reviews:

Related manuals for U.S. Robotics 56K Voice

Brands by name

Popular brands